TM
Patent Pending
|
TM
|
| Motorcycle Safety Products | |
|
|
| "You shouldn't ride without it..." | |
  |
 |
 |
 |
 |
| Turn Signal Indicator | |||
|
Package Contents: |
 |
||
|
Item
|
Qty
|
Description | |
|
1
|
1
|
Blinksafe Indicator Assembly | |
|
2
|
1
|
Wiring Harness |
|
|
3
|
1
|
¾" x 1" Adhesive Backed Velcro Hook & Loop Pair | |
|
4
|
3
|
Quick Tap Wire Splice | |
| Fairing Mount Installation Instructions | |||
|
1.
|
Turn the motorcycle
ignition to off and disconnect the battery for safety. |
|
2.
|
Remove body panels
as required to gain access to the front turn signal wiring harnesses. This
will enable routing of the Blinksafe Indicator Assembly wire and the Wiring
Harness wires. The motorcycle's front turn signal wiring harnesses will
be connected to the left and right turn signal lamp wires. |
|
3.
|
Identify the positive (+) wire and negative (-) or ground wire in the front turn signal wiring harnesses near the left and right turn signal lamps. Label with masking tape if needed. Consult your dealer, repair manual, or repair shop for assistance if needed. |
 |
|
4.
|
Identify a desired location for the Blinksafe Indicator Assembly. An ideal location is one where the Blinksafe Indicator Assembly will be in your peripheral field of view when you are watching the road ahead of you. The Blinksafe Indicator Assembly lamps should be aimed toward your eyes to ensure visibility while riding during the day. |
 |
|
5.
|
Connect the Blinksafe Indicator Assembly to the Wiring Harness, and layout the assembly from your desired location of the Blinksafe Indicator Assembly to the front turn signal wiring harnesses near the left and right turn signal lamps. The use of clear tape or masking tape to temporarily hold the assembly in place is recommended to allow for experimentation with different mounting locations and wire routing paths. Note: The Blinksafe Indicator Assembly and Wiring Harness wires are long enough to fit most motorcycles. If your motorcycle requires longer wires contact us via email at info@blinksafe.com. |
 |
|
6.
|
Attach 1 Quick Tap Wire Splice to the positive (+) wire of the Left Turn Signal lamp. Insert one of the red wires from the Wiring Harness into the Quick Tap Wire Splice. Crimp the Quick Tap Wire Splice with pliers and snap the cover closed. The Quick Tap Wire Splice is for 18-22 gauge wires. The red and black wires of the Wiring Harness are 20 gauge. If you do not know the wire gauge of your turn signal lamp wires you may manually splice the Wiring Harness wires into your turn signal lamp wires. |
 |
|
7.
|
Repeat step 6 with
the positive (+) wire of the Right Turn Signal lamp and the other red wire
from the Wiring Harness |
 |
|
8.
|
Repeat step 6 with
one of the ground (-) wires from the left or right turn signal lamps and
with the black wire from the Wiring Harness. |
|
|
9.
|
Wrap the Wire Splices and Wiring Harness circuit board with electrical tape. |
|
10.
|
Reconnect the battery
and turn the motorcycle ignition to on to supply power to the turn signals. |
|
11.
|
Test the Blinksafe
Indicator by turning on the Left Turn Signal. The Blinksafe Indicator should
flash in unison with the left turn signal lamp. Repeat with the Right Turn
Signal. |
|
12.
|
Once the Blinksafe
Indicator is connected and working, temporarily mount the indicator on your
fairing and aim the lamps toward your eyes when you are in the riding position
on your motorcycle. Turn on one of your turn signals to make sure you can
see the lamps when you focus on the road ahead. |
|
13.
|
After confirming
a good mounting location, apply one of the adhesive backed Velcro pads to
the mounting location on your bike and apply the other to the back of the
Blinksafe Indicator. The Velcro pads are sized to completely cover the back
of the Blinksafe Indicator. It is most important that the Velcro pad covers
the rounded back side of the Blinksafe Indicator to allow you to adjust
the aim of the indicator lamps. During bright days the indicator lamps should
be aimed directly toward your eyes. At night you may want to aim the lamps
away from your eyes slightly to lessen the intensity of the lamps. You may
trim the Velcro pads as needed or desired. |
 |
|
14.
|
The Blinksafe Indicator
wire may be formed or folded to follow the contour of your fairing or motorcycle
body panels. If you wish to secure the wire permanently, apply clear silicone
adhesive or caulking to attach the wire to your motorcycle. |
|
15.
|
Register your Blinksafe Turn Signal Indicator via www.blinksafe.com/register. |